Lust Rapid Recoat Marine Spar Varnish

FREQUENTLY ASKED QUESTIONS

• What is the difference between high gloss and matte TotalBoat Lust Varnish?

  TotalBoat Lust Spar Varnish creates a high-gloss finish. Lust Matte is not intended for use as a base coat. For a low-sheen finish, we recommend using Lust Gloss or Gleam Gloss for sealer (base) and build coats. Finish with a topcoat of Lust Matte.
• Can Lust Varnish be used to overcoat non-varnish wood finishes?

  Yes. Lust is compatible with marine wood finish products and ‘rapid’ application wood finishes commonly used in the marine industry as varnish alternatives.
• Can I overcoat Lust Spar Varnish with other varnishes?

  Yes. Many customers use Lust for the build coats, and finish off with a different 1-part varnish to match the finished look they have on their boat. Note that we do not recommend applying 2-part varnish over Lust.
• Can Lust be applied over other varnishes?

  Yes. Lust can also be applied over other cured varnishes (both 1 and 2 part urethane) in good condition. Lightly scuff with 320 grit sandpaper and apply.
• Can this marine varnish be applied over wood oils?

  Customers often ask if this varnish can be applied over teak oil, penetrating oil stains, shellac, lacquer, and other finishes. In general, we recommend using this varnish over bare wood or existing varnish finishes in good condition.
• Can it be applied over wood stain?

  Yes, Lust can be applied over wood stain, but it is highly recommended to always make a sample piece and see if there are any incompatibilities.
• Is Lust a hard enough finish for use on a table top or coffee table?

  While TotalBoat Lust will create a beautiful finish on all kinds of wood, epoxy is more durable and we recommend TotalBoat Tabletop Epoxy for bar top and table top applications.
• Can Lust be used as a clear coat over paint?

  We do not recommend using Lust as a clear coat over paints, whether 1-part polyurethane or other types of finish. It is not a clear finish, to begin with. However, can be used over epoxy.
• Does Lust Spar Varnish dry clear, or does it have a color?

  Lust will dry to a deep clear amber color. It is not a clear finish.
• What is the best way to apply this varnish?

  You can apply by brush, roll and tip, or spray. When spraying, reduce 25-100% with xylene, as conditions and spray equipment will dictate, but less reducer will yield higher gloss.
• Do you need to thin Lust?

  Thinning is recommended for initial sealer coats. Alternately, use TotalBoat Wood Sealer Varnish Primer in lieu of thinned varnish. After seal coats are applied, thinning is not necessary, but you may reduce up to 25% to improve flow or extend working time.
• What do you thin this varnish with?

  For brushing and rolling, use TotalBoat Special Brushing Thinner 100. If spraying, use TotalBoat Spray Thinner 101.
• How long do I have to wait before applying another coat?

  Lust Varnish lets you recoat in 1 hour (at 72 F), letting you apply up to 5 coats in one day. If applying 4 or more coats in one day, wait up to 48 hours before sanding and applying subsequent coats.
• Do I need to sand between coats?

  No. We do recommend sanding before the final coat before the smoothest possible finish.
• What is the typical coverage?

  The coverage for Lust Varnish is between 360-400 sq ft per gallon.
• What is the temperature range for application?

  Lust will cure when the product, application surface, and outside/ambient temperatures are as low as 45°F. However, you will achieve the best results when temperatures are between 60°F and 100°F.
• How do I maintain the varnish finish over time?

  To maintain the best finish and clarity, annual maintenance coats are recommended for brightwork exposed to UV rays. Sand lightly with 320-grit sandpaper or a Scotch-Brite pad, remove sanding residue, and apply maintenance coats.
• How do you clean brushes after varnishing with Lust?

  We recommend TotalBoat Special Brushing Thinner 100 for varnish cleanup, including brushes and painting tools.